Full Lace Wig Removal: Are You Sure You Doing It Right?
Everyone appreciates a versatile, well-rounded and long-lasting full lace wig. It is the easiest to install and remove yet still gives you a gorgeous look. It is definitely worth the money to spend on a high-quality full lace wig. In this article, we will show you how to full lace wig removal process as well as how to install it.
Full lace wig installation: Glue-in method
Main of Contents
Step 1: Preparation
The first thing you need to do is to wash your hair. It needs to be clean and oil-free before the installation. After washing, dry it thoroughly. You can let the hair air dry if you have time, or use a blow dryer. Nothing is worse than damp hair under full lace wig as it is an excellent environment for the harmful bacteria to grow.
Secondly, you want to braid your hair into a cornrow. The reason for that is a clean and flat surface underneath the hair cap. If you don’t braid your hair or make your real hair neat and tight underneath that cap, they can get tangled and shed quickly. Furthermore, braiding helps you avoid all the lumps and bumps, which reveals that you are wearing a wig. Finally, wear a hair cap to tame everything down.
Step 2: Trim the lace
It’s time for some final trimming. The principal is simple: cut the lace where it is visible. You only have to do it the first time you buy. So try to be careful with that.
Take small, sharp scissors to trim the lace. Be cautious and trim as close to the hairline as possible. You do not want any lace shown through the hair. Cut a small amount at a time so that you can achieve the precision you want.
Step 3: Installation
Then, you can spray a little scalp protecting product on your hair. The product acts as a protective barrier between the scalp and the adhesive. If your skin is sensitive, clean the skin gently with a cotton round damped with light alcohol. This removes any excess oil you may have that prevents the adhesive from sticking properly
You can apply a thin layer of adhesive around your hairline to prep for the installation. Use a hairdryer to let the adhesive set for around 30 seconds. The adhesive is ready when it becomes a little tacky.
Now, it’s time to put on the wig. Start with the middle front of the wig. Place that exactly when you want it to be. Press the part down firmly and hold for around 1 minute. Be patient and wait for the front middle part to set.
After that, grab the two sides and pull them far from each other. The point of that is to keep the hairline as flat as if it is your real hairline. Stick the sides on and continue to hold them for 1 minute. Once you are done setting the front hairline, adjust the back so that the wig can fit you properly.
For the final touch, you can adjust the parting and the baby hair to look natural. Comb the hair through and do any styling you want. A flat iron may come in handy if you want to smooth down the top part to mimic your real hair.
Full lace wig removal: Glue-in method
- Step 1: Brush your hair up into a ponytail so that you can see all the edges.
- Step 2: Saturate a washcloth or a cotton round in an adhesive remover liquid. You can buy the product easily at the supermarket or online. If you cannot find it, you can use shampoo instead. Rub it gently into the edges. Be careful! You don’t want the product to get to your eyes.
- Step 3: Be patient! The full lace wig will come off
- Step 4: Wash for hair and rinse thoroughly with water
You are doing it wrong!
Full lace wig installation: Sew-in method
Step 1: Turn the full lace wig inside out. Put the hair of the wig into a ponytail so that it does not get into the way when you sew the wig on.
Step 2: Use a needle and a thread that is similar to the hair color. Take one wig clip and place it at the bottom middle part of the wig so that the clip’s teeth are facing you.
Step 3: Insert the needle underneath the wig and through the hole of the clip. Wrap the thread around the needle twice. Continue to sew in the next hole. Insert the needle through and hole and down the wig. Repeat the procedure until every hole of the clip is sewn down.
Step 4: Place another clip around 3 inches away from the first clip. Do the same stitching process as you did with the first clip
Step 5: It’s important to sew in 2 clips on the sides to secure the edges. Before you sew in, make sure the hairline look seamless and flat. Do not put any clip in the front hairline as it is noticeable.
Step 6: Flip the wig around and place it on your head. Insert all the clips into your hair to secure the wig. Some hair manufacturers may already have clips sewn in for you. In this case, you only need to put the wig on.
Step 7: Groom and style the wig however you want to make it look more natural and effortless.
Full lace wig removal: Sew-in method
The full lace wig removal process of this method is super simple. Because all the hair clips are sewn in, all you need to do is put the wig down. You do not even have to remove the thread because you are going to need it for the next year time. If you need to remove the clips, take a scissor and cut the thread. Be careful! You don’t want to cut the real hair.
We hope you have got the answer to the question “How to do full lace wig removal?” It is a challenging yet fun process. Just be a little extra careful, take your time, and you will be just fine!
If you like this article about full lace wig removal, please SHARE with your friends!
Follow Layla Blog for wonderful hair tips!