4 Things I Wish I Knew About How To Apply Glueless Full Lace Wigs
Many full lace wigs users assume that to apply it to your head, glue is needed. If you think that is too complex or time-wasting, choose glueless full lace wigs instead. The glueless appliance method is more convenient and easier even for a beginner. Hence, if you want to know how to use this method, let’s read through this paper of Layla Hair about how to apply glueless full lace wigs.
How to Put On Glueless Full Lace Wigs?
Main of Contents
Glue or adhesive for wigs also make the pores stuck and ruin the hair follicles. They can stop the growing process of your hair strands and make your hair look much thinner.
Moreover, Wig glue contains latex as a common ingredient, which often triggers allergic and irritation reactions for full lace wigs users. And these bad effects also can cause rashes, hair loss, and lifeless hair.
Perhaps some of you have ever experienced one of these problems when using wig adhesive and just want to find a safer choice. There is no doubt that glueless full lace wigs can somehow better your issues and save your hair from damaging.
Get Ready For Glueless Full Lace Wigs How To Apply
At the begging of the appliance process, you have to prepare your hair. You may need to make your hair soft, slat and smooth. The selections depending on your hair texture, length, and types.
In case your hair is a shortcut or on the thinner side, simply hold it back to make a ponytail or braid it at the nape of your neck. After that, use some bobby pins to fix the braid or pony firmly against your head.
In case you got long and thick hair, it is better to make cornrows. Once you do that, you do not have to do any special steps and just pin them up
In the Next step, you can apply the lace. But it is just temporary. This lace is not stick on your scalp as using glue.
If the lace does not match your skin tones, you can dye it for a perfect match. That will give you a more natural look.
How to Wear Glueless Full Lace Wigs?
In the glueless method, there are also various ways to apply glueless full lace wigs. Let’s check it out on how to apply glueless full lace wigs. Then pick the one you think it fits you!
Using Wigs Clips And Combs
Clips and combs are really cheap. In general, glueless lace wigs will have both combs or clips attached to them. They are usually placed at the crown of your head, near each ear and at the back of your nape one-by-one.
Step 1: Reverse your full lace wig inside out. Gather your hair into a ponytail or cover it with a fastener to make sure it is on the way. Then start applying.
Step 2: Sew the wigs clip by using a weaving needle with a thread that has the same color as your hair color to make it less visible.
Step 3: Each wig clip’s bottom should be at the middle bottom of the wigs. And the teeth of clips must face outside.
Sew through every hold on each clip by the needle you have prepared.
Step 4: Repeat step 3 but locate the next wig 3 inches away from the first one. Then, attach the clip to the cap.
Step 5: Reverse once more time to make the full lace wigs into the right side. Don’t place any clips at the frontal side of wigs. Since your hairline will be more visible.
Step 6: Apply the wigs to your hair and take off the fastener.
Using Wig Tape
Wig tape is an adhesive tool. However, it is not as strong as glue and causes less damage. There are two forms of tape, strips, and roll. Both of them are good to use.
Step 1: Use a cotton ball with alcohol to clean along your hairline.
Step 2: After that, pull your hair back smoothly following the hairline to prevent tugging or easily-remove in the near future.
Step 3: Apply a small amount of scalp protector ( or liquid band air) under the hairline area. Then peel off the tape and apply it at which you want the wig to locate.
Step 4: Place the full lace wigs and press it down for a few seconds to make sure it cannot pop up.
Using An Elastic Band
This method can be the easiest one on how to apply glueless full lace wigs.
The elastic band can be found easily at any craft store in your town.
For the elastic band method, you can purchase an elastic band from your local craft store. After purchasing, sew the band along the back of the wig at the nape.
The Elastic band method will help your full lace wigs become flat and smooth. Moreover, this method is perfect for thick and long wigs.
Using the Wig Grip
Another way on how to fix glueless full lace wigs is Using the wig grip.
Wig grip is a band which helps to make the wig stay stable. They differ in color so make sure the one you pick is similar to your skin tone.
Step 1 – Locate the wig grip under your edges and make sure it connected to the velcro ends. Leave it to stay comfortably in place, you don’t need to tighten it hard.
Step 2 – Carefully apply the full lace wig onto your head where you want it to go. Once you attach it, it will stick firmly. Therefore, to change the lace wigs, you should gently pull the hair in the way you desire. Lastly, pull the wigs back to your head.
Step 3 – Pin your hair backward and check the edges area to gain a more natural effect.
Step 4 – Take out your hair from the clips and it’s done!
What Method Will You Pick?
We hope that thanks to this paper, you will know more about glueless lace wigs and how to apply glueless full lace wigs.
If you want to ask any questions or give us suggestions or feedback, we are glad to know and answers all your questions!
And if you are interested in getting one for your own, contact Laylahair to get consulted on the best products.